Bartels mp6 Micropumps
Rated 3.5/5 based on 11 customer reviews

Bartels mp6 Micropumps

Bartels mp6 series micropumps are a revolution in the field of microfluidics. Capable of transporting a very small quantity of liquid or gas, the micropumps of the mp6 series are characterised by the combination of 2 piezo actuators in a ultra-compact unit and very light weight.
Available in different versions (mp6-hyb, mp6-liq, mp6-gas, mp6-gas+, mp6-pi and mp6-pp), you are sure to find the right mp6 micropump for your application.
Available within 1 week
€29.00
Bartels mp6 series micropumps are a revolution in the field of microfluidics. Capable of transporting a very small quantity of liquid or gas, the micropumps of the mp6 series are characterised by the combination of 2 piezo actuators in a ultra-compact unit and very light weight.
Available in different versions (mp6-hyb, mp6-liq, mp6-gas, mp6-gas+, mp6-pi and mp6-pp), you are sure to find the right mp6 micropump for your application.

With an ultra-simple design and construction, these mp6 micropumps can perform a wide range of tasks, including moving diagnostic samples through a microfluidic device, dosing lubricants, supplying sensors with a gas sample, mixing solutions, and much more.

  • Wide range of mp6 micropumps for liquids (mp6-liq, mp6-pi, mp6-pp), liquids & gases (mp6-hyb) and gases (mp6-gas, mp6-gas+)
  • Flow rates from 8 µL/min up to >10 mL/min
  • Ultra-compact (30 x 15 x 3.8 mm) and light (2 g only)
  • Good temperature resistance
  • Almost entirely made of plastic, various wetted materials for a wide chemical compatibility

Principle

Bartels micropumps are based on a piezoelectric diaphragm in combination with passive check valves. When applying voltage, a piezo ceramic mounted on a coated brass membrane is deformed, and the medium is being displaced out of the pump chamber below.

          

 

mp6 Micropumps

The flow rate of the pumps shows a linear dependency on the back pressure. At 0 mbar back pressure the maximum pump rate can be achieved and at the maximum back pressure the flow rate is decreased to 0 mL/min. The relation of pressure and flow rate is linear.

The typical lifetime of the pumps is 5000 h.

 

Micropumps for liquids

mp6-liq:

  • 8 µL/min - 14000 µL/min
  • wetted material: PPSU (polyphenylsulfone)
  • typ. back pressure: 800 mbar

mp6-pi:

  • 8 µL/min - 8000 µL/min
  • wetted materials: PI foil (Polyimid) & PPSU (Polyphenylsulfone)
  • typ. back pressure: 500 mbar

mp6-pp:

  • 8µL/min - 4000 µL/min
  • typ. back pressure 500mbar @100 Hz, 250 Vpp, SRS signal
  • wetted materials: PP (Polypropylene)
  • typ. back pressure: 500 mbar
Micropumps for liquids & gases

mp6-hyb:

  • liquids: 8 µL/min - 10000 µL/min, typical flow rate 8 mL/min & typical back pressure 500 mbar @100 Hz, 250 Vpp, SRS signal
  • gases: from 12 mL/min  & min. back pressure 80 mbar @100 Hz, 250 Vpp, SRS signal, wetted material: PPSU (polyphenylsulfone)
Micropumps for gases

mp6-gas:

  • typical flow rate: 20 mL/min
  • material in contact: PPSU (Polyphenylsulfone)
  • typ. back pressure: 100 mbar

mp6-gas+:

  • typical flow rate: 20 mL/min
  • material in contact: PPSU (Polyphenylsulfone)
  • typ. back pressure: 150 mbar

    Common specifications

    Pump type

    Piezoelectric diaphragm pump

    Number of actuators

    2

    Dimensions without connectors

    30 x 15 x 3.8 mm

    1.1811 x 0.5906 x 0.1498 in.

    Weight

    2 g

    Fluidic connectors

    Barbed tube clip (outer diameter 1.9 mm, length 3.5 mm) 2

    Electric connector

    Flex connector 1.25 mm pitch

    Power consumption NO

    ~ 50 mW 3

    Self-priming

    Yes 4

    Operating temperature

    0-70 °C

    Life time

    5000 h 5

    IP rating

    IP33 6

    1 Typical values. Values can vary under application conditions. Content is subject to changes without notice.

    2 Recommended tubing: Tygon tubing 1.3 mm inner diameter.

    3 Conditions: settings mp-x: 100 Hz, 250 V, SRS

    4 Conditions: Suction pressure >10 mbar, DI water, settings mp-x: 100 Hz, 250 V, SRS, the volume flow will be reached after a few minutes of operation time.

    5 Conditions: settings mp-x: 200 Hz, 250 V, SRS

    6 Can be changed to IP44.

    Material and drivers

     Pumping media

    mp6-hyb: liquids and gases

    mp6-liq, mp6-pp, mp6-pi: liquids and mixtures

    mp6-gas, mp6-gas+: gases

    Material in contact with media

    mp6-hyb, mp6-liq, mp6-gas, mp6-gas+: Polyphenylsulfone (PPSU)

    mp6-pi: Polyimid foil (PI), Polyphenylsulfone (PPSU)

    mp6-pp: Polypropylene (PP), Polyimid foil (PI)

    Suitable pump driver

    mp6-hyb, mp6-pi, mp6-pp, mp6-gas, mp6-gas+: mp-x, mp6-EVA, mp6-OEM, mp6-QuadOEM and mp6-QuadKEY

    mp6-liq: mp-x, mp6-XEVA, mp6-XOEM, mp6-QuadOEM and mp6-QuadKEY

    Measured with mp-x controller at 100 Hz, 250 V, SRS.

    mp6-hyb

    Liquids – water

    Controllable flow range9 Q

    8µl/min – 10000 µl/min

    typ. flow rate Q (p=0)

    8ml/min 1

    typ. back pressure p (Q=0)

    500 mbar (7.25 psi) 1

    Gases – air 

    typ. volume flow Q (p=0)

    20 ml/min 2

    typ. back pressure p (Q=0)

    80 mbar (1.16 psi) 2

    mp6-liq

    Liquids – water

    Controllable flow range9 Q

    8µl/min – 14000 µl/min

    typ. flow rate Q (p=0)

    11ml/min 2

    typ. back pressure p (Q=0)

    800 mbar (11.6 psi) 2

    mp6-pi

    Liquids – water

    Controllable flow range3 Q

    8µl/min – 8000 µl/min

    typ. flow rate Q (p=à)

    6 ml/min 1

    typ. back pressure p (Q=0)

    500 mbar (7.25 psi) 1

    mp6-pp

    Liquids – water

    Controllable flow range3 Q

    8µl/min – 4000 µl/min

    typ. flow rate Q (p=à)

    4ml/min 1

    typ. back pressure p (Q=0)

    500 mbar (7.25 psi) 1

    mp6-gas & mp6-gas+

    Gases

    typ. volume flow Q (p=0)

    20 ml/min (300 Hz) 2

    typ. back pressure p (Q=0)

    mp6-gas: 100 mbar (300 Hz)

    mp6-gas+: 150 mbar (300 Hz)

    1 Conditions: DI water (25°C), room temperature 23°C, settings mp-x: 100 Hz, 250 V, SRS

    2 Conditions: air, room temperature 23°C, mp-x: 300 Hz, 250 V, SRS

    3 Controllable with frequency, voltage, signal form and more. Please contact us for more information.

    Payment Terms

    You can either order and pay via credit card or invoice (through a purchase order). Please note that some products are not available for direct purchase: just click "Request a Quote" on the product page and fill in the form to get more informations!

    Credit card 

    • Add your products to the cart
    • In the cart page, click on Proceed to Checkout
    • Complete your credit card informations (don't worry, we are using Stripe, a PCI-certified program specialized in online transactions)
    • That's it! You will receive an order confirmation within a few minutes, and our team will send you the invoice.

    Invoice

    • Add your products to the cart
    • In the website header, click on Request a Quote
    • Fill in the required informations, then click on Submit Quote
    • Our team will send you a quote shortly
    • After receiving the quote, just send your purchase order at contact@darwin-microfluidics.com
    • Our team will complete your purchase and send you the invoice!

    If you wish to pay in USD, AUD or GBP, please specify it in your PO. We can add the converted value in the required currency to the quote if requested.

     

    Worldwide shipping

    We ship worldwide from our warehouse in France.

    The shipping charges are calculated based on the weight of the package and the country of destination: you can estimate the shipping cost on the cart page. We try to offer you the best shipping rates and services, shipping all our orders through DHL Express. Generally, your order reaches your lab in only 2 to 3 days after we send it, no matter the destination! 

    Please note that our shipping incoterms are DAP (Delivered At Place). Please contact us if you prefer using your own courrier account or have any question!

    Customer Reviews

    No reviews yet
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)

    Customer Reviews

    No reviews yet
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)
    0%
    (0)