mzr-2521X1 micro annular gear pump from HNP Mikrosysteme generates low pulsation, high precision flow from 15 µL/min to 9 mL/min (minimum dispensing of 0.25 µL). The integrated motion controller allows to precisely control the pump and program complex workflows.
The pump is suitable for dosage of low viscosity liquids such as deionized water, watery solutions, methanol, solvents, oil and lubricants.
General
Micro annular gear pumps generate a near pulsation-free and accurate flow rate down to a few µL/min. The low-pressure series pumps are designed for the dispensing of low-viscosity liquids, such as aqueous solution, solvents, oils and lubricants.
The mzr-2521X1 is the smallest pump from the low-pressure series:
- Based on the mzr-2521 pump, with an integrated high-precision controller
- Flow range: 15 µL/min - 9 mL/min
- Min. dispensing volume: 0.25 µL
- Differential volume range: 0 - 1.5 bar (22 psi)
- Integrated motion controller: control the start/stop, speed and direction of the pump through analog and RS-232 interfaces, built-in potentiometer or mzr Pump Control software (included)
- 70 W, 24 V DC, 3 A power supply included
Features & Benefits
- Near pulsation-free and accurate flow rate down to 1% (CV value): competes with the best syringe pumps
- Ideal for recirculation: open reservoirs, without the pulsatility of peristaltic pumping (low shear stress)
- Wide range of applications, from analytical chemistry to cell culture and point-of-care diagnostics
- Version with integrated controller: program and control your pump easily
- 1/4-28 manifold in PEEK: easily connect the pump to any tubing
- Compact size: Ø 22 mm, length 89 mm
Each pump component is available in a variety of materials to meet your needs:
Rotor | Housing | Shaft seal (not in contact with fluids) | Static seals |
|
|
graphite-reinforced PTFE |
|
Content
1x mzr gear pump with X1 module
1x 1/4-28 PEEK manifold
1x S-G05 controller box
1x Power supply
Principle
Two eccentrically mounted rotors are intermeshed with their cycloid gearing. This results in a system of several sealed pumping chambers exists at all times. With a tooth ratio of 6/7, six individual chambers are created.
As the rotors turn around their offset axes, the volume of the pumping chambers increases on the induction side and simultaneously decreases on the delivery side of the pump. A homogeneous and low-pulsation flow rate is generated between the kidney-shaped inlet and outlet which also combines several pumping chambers at the same time.
Specifications
Flow rate | 0.015 - 9 mL/min |
Smallest dosage volume | 0.25 µL |
Displacement volume | 1.5 µL |
Differential pressure range | 0 - 1.5 bar (22 psi) |
Maximum inlet pressure | 1 bar (15 psi) |
Liquid temperature range | -20 ... +60 °C (-4 ... +140 °F) |
Viscosity range | 0.3 - 100 mPas |
Precision CV | 1 % (Coefficient of variation CV) |
Velocity range | 10 - 6000 rpm |
Fluid connection |
PEEK 1/4-28 manifold (fittings not included) |
Wetted parts |
Housing and rotor: stainless steel 316L, ceramics, tungsten carbide Ni based, epoxy resin, optional: alloy C22 (2.4602) instead of stainless steel, ceramics instead of tungsten carbide Shaft seal: graphite-reinforced PTFE, stainless steel 316L Static seals: FFKM, optional: EPDM |
Motor | DC-motor with graphite brushes, assigned power rating 3 W, nominal voltage 18 V, digital magnet encoder 16 counts per turn |
Controller | Integrated motion controller |
Interface | 0-10 V, RS-232, 1 digital input/output |
Electrical connection | 8-pole connector |
Power supply | 70 W, 24 V DC, 3 A (included) |
Dimensions (L x W x H) | Ø 22 mm, length 89 mm |
Weight | 125 g + weight of the PEEK manifold |
Documentation
mzr-2521X1 micro annular gear pump from HNP Mikrosysteme generates low pulsation, high precision flow from 15 µL/min to 9 mL/min (minimum dispensing of 0.25 µL). The integrated motion controller allows to precisely control the pump and program complex workflows.
The pump is suitable for dosage of low viscosity liquids such as deionized water, watery solutions, methanol, solvents, oil and lubricants.
General
Micro annular gear pumps generate a near pulsation-free and accurate flow rate down to a few µL/min. The low-pressure series pumps are designed for the dispensing of low-viscosity liquids, such as aqueous solution, solvents, oils and lubricants.
The mzr-2521X1 is the smallest pump from the low-pressure series:
- Based on the mzr-2521 pump, with an integrated high-precision controller
- Flow range: 15 µL/min - 9 mL/min
- Min. dispensing volume: 0.25 µL
- Differential volume range: 0 - 1.5 bar (22 psi)
- Integrated motion controller: control the start/stop, speed and direction of the pump through analog and RS-232 interfaces, built-in potentiometer or mzr Pump Control software (included)
- 70 W, 24 V DC, 3 A power supply included
Features & Benefits
- Near pulsation-free and accurate flow rate down to 1% (CV value): competes with the best syringe pumps
- Ideal for recirculation: open reservoirs, without the pulsatility of peristaltic pumping (low shear stress)
- Wide range of applications, from analytical chemistry to cell culture and point-of-care diagnostics
- Version with integrated controller: program and control your pump easily
- 1/4-28 manifold in PEEK: easily connect the pump to any tubing
- Compact size: Ø 22 mm, length 89 mm
Each pump component is available in a variety of materials to meet your needs:
Rotor | Housing | Shaft seal (not in contact with fluids) | Static seals |
|
|
graphite-reinforced PTFE |
|
Content
1x mzr gear pump with X1 module
1x 1/4-28 PEEK manifold
1x S-G05 controller box
1x Power supply
Principle
Two eccentrically mounted rotors are intermeshed with their cycloid gearing. This results in a system of several sealed pumping chambers exists at all times. With a tooth ratio of 6/7, six individual chambers are created.
As the rotors turn around their offset axes, the volume of the pumping chambers increases on the induction side and simultaneously decreases on the delivery side of the pump. A homogeneous and low-pulsation flow rate is generated between the kidney-shaped inlet and outlet which also combines several pumping chambers at the same time.
Specifications
Flow rate | 0.015 - 9 mL/min |
Smallest dosage volume | 0.25 µL |
Displacement volume | 1.5 µL |
Differential pressure range | 0 - 1.5 bar (22 psi) |
Maximum inlet pressure | 1 bar (15 psi) |
Liquid temperature range | -20 ... +60 °C (-4 ... +140 °F) |
Viscosity range | 0.3 - 100 mPas |
Precision CV | 1 % (Coefficient of variation CV) |
Velocity range | 10 - 6000 rpm |
Fluid connection |
PEEK 1/4-28 manifold (fittings not included) |
Wetted parts |
Housing and rotor: stainless steel 316L, ceramics, tungsten carbide Ni based, epoxy resin, optional: alloy C22 (2.4602) instead of stainless steel, ceramics instead of tungsten carbide Shaft seal: graphite-reinforced PTFE, stainless steel 316L Static seals: FFKM, optional: EPDM |
Motor | DC-motor with graphite brushes, assigned power rating 3 W, nominal voltage 18 V, digital magnet encoder 16 counts per turn |
Controller | Integrated motion controller |
Interface | 0-10 V, RS-232, 1 digital input/output |
Electrical connection | 8-pole connector |
Power supply | 70 W, 24 V DC, 3 A (included) |
Dimensions (L x W x H) | Ø 22 mm, length 89 mm |
Weight | 125 g + weight of the PEEK manifold |
Documentation